Roller Chain vs. Drag Chain vs. Slider Bed Conveyors

Equipment Solutions For The Recycling Industry

The short answer

All three move material through a recycling plant. They differ in how they carry the load. Roller chain rides on wheels. Drag chain pulls a belt along the frame. Slider bed slides a rubber belt over a steel deck.

Roller chainDrag chainSlider bed
How it movesChain with wheels that ride on railsChain that drags the belt, usually without wheelsRubber belt sliding on a steel deck, driven by a head pulley
Best atHeavy, rough infeed to balers and shreddersOil-free plants and very heavy loadsLong runs and moving material from one point to the next
OilOiled chain and rollersOil freeNo chain to oil
CleatsTall cleats, 4 to 6 inchTall cleats, 4 to 6 inchShort cleats, 1 to 2 inch
Where you see itPits and inclines feeding a machineIndoors, most often in paper plantsLong runs, pits under box lines, transfers

Roller chain

The belt rides on two strands of chain. Wheels on the chain run on rails down each side. The wheels take the weight, so the belt can carry heavy, rough material without dragging.

That makes roller chain the usual pick for an infeed. It loads in a pit or hopper and climbs to a baler or shredder, at up to 45 degrees. It is also the bulk of what we build, in RC 6-3, 9-4 and 9-5 sizes, rated from 4,650 to 12,700 lbs per strand.

The trade-off is oil. The rollers and bearings need it, and some of it drips onto the rails and the floor.

Drag chain

A drag chain conveyor pulls its belt along the frame instead of rolling it on wheels. There are no oiled rollers, so it runs oil free. That is why paper plants pick it. Oil and paper dust do not mix, and nobody wants oil on the material.

Drag chain can also go stronger than roller chain. When a load is too heavy for roller chain, we move to a heavier drag chain.

Our most common model is the DC131. The DC111 runs a stronger chain. We also build other chain styles on request.

Slider bed

A slider bed conveyor slides its rubber belt across a solid steel deck. A head pulley drives the belt by friction. There is no chain and no rollers, just the belt.

That makes it a strong fit for long runs. We have built slider beds up to 300 feet. They work well in a pit under a corrugating line, and for hauling scrap away from a paper line.

A slider bed is not the pick for heavy weight or steep angles. It takes cleats of 1 or 2 inches. When you need tall, aggressive cleats to move more material or heavy weight, go to roller chain or drag chain.

Which one fits your plant

  • Feeding a baler or shredder from a pit? Start with roller chain.
  • Need it oil free, like in a paper plant? Look at drag chain.
  • Moving very heavy loads? Roller chain or a heavier drag chain.
  • Long run, or a pit under a box line? A slider bed is often the answer.
  • Very little height under a machine? A low-profile slider bed can fit where others cannot.

Most plants run more than one type. We design the whole line so each conveyor hands off cleanly to the next.

Questions buyers ask

What is the difference between a roller chain and a drag chain conveyor?

A roller chain conveyor rides on oiled wheels that run on rails. A drag chain conveyor pulls its belt along the frame and runs oil free. Roller chain is the usual pick for infeeds. Drag chain is common in paper plants and for very heavy loads.

What is a slider bed conveyor?

A conveyor whose rubber belt slides across a solid steel deck, driven by a head pulley. It moves material flat or up a gentle incline.

How long can a slider bed conveyor be?

We have built them up to 300 feet.

Can one plant use all three?

Yes. Many do. We design each conveyor to hand off to the next.

Not sure which one you need?

Tell us the machine and the material. We will tell you which conveyor fits.